logo Professor Uday S Dixit

Department of Mechanical Engineering

Indian Institute of Technology Guwahati

Journals

Total Number of Journal Publications: 72

Selected Publications:

  1. S. Mahto, A.K. Gogoi, U.S. Dixit, 2016, A comparative study of improved dynamics of single link flexible revolute-jointed robotic manipulator, Procedia Engineering, Vol. 144, pp. 425 - 434.
  2. S.M. Kamal and U.S. Dixit, 2016, A study on enhancing the performance of thermally autofrettaged cylinder through shrink-fitting. ASME. Journal of Manufacturing Science and Engineering, Vol. 138, No. 9, pp. 094501-094501-5. doi:10.1115/1.4033083.
  3. S.M. Kamal and U.S. Dixit, 2016, A comparative study of thermal and hydraulic autofrettage, Journal of Mechanical Science and Technology, Vol. 30, No. 6, pp. 2483 - 2496.
  4. W.G. Jiru, M. Ravi Sankar and U.S. Dixit, 2016, Laser surface alloying of copper, manganese and magnesium with pure aluminum substrate, Journal of Materials Engineering and Performance, Vol. 25, Issue 3, pp. 1172 - 1181. DOI: 10.1007/s11665-016-1922-x.
  5. S. M. Kamal, A.Ch. Borsaikia and U. S. Dixit, 2016, Experimental assessment of residual stresses induced by the thermal autofrettage of thick-walled cylinders, Journal of Strain Analysis for Engineering Design, Vol. 51(2), pp. 144–160.
  6. V. Yadav, A.K. Singh and U.S. Dixit, 2015,  Inverse estimation of thermal parameters and friction coefficient during warm flat rolling process, International Journal of Mechanical Sciences, Vol. 96–97, June 2015, pp. 182–198 doi: 10.1016/j.ijmecsci.2015.04.001
  7. S.M. Kamal and U.S. Dixit, 2015, Feasibility study of thermal autofrettage of thick-walled cylinders, ASME Journal of Pressure Vessel Technology, Vol. 137, Issue 6, 061207-061207-18, doi: 10.1115/1.4030025.
  8. N. J. Baishya, D. Sharma and U.S. Dixit, 2014, Optimization of pressure vessel under thermo-elastic condition, Journal of Institution of Engineers (India), Series C, Vol. 95, Issue 4, pp. 389-400.
  9. V. Yadav, A.K. Singh and U.S. Dixit, 2014, An approximate method for computing the temperature distributions in roll and strip during process, Proc. IMechE,  Part B:, Journal of Engineering Manufacture, Vol. 228, pp. 1118-1130.
  10. S. Mahto and U.S. Dixit, 2014, Shape optimization of revolute-jointed rigid-flexible manipulator, Journal of Institution of Engineers (India), Series C, Vol. 95, Issue 4, pp. 335-346.
  11. M. Hazarika, S. Deb,  U.S. Dixit and J.P. Davim, 2011, Fuzzy set based setup planning system with ability for online learning,  Proc. IMechE,  Part B: J. Engineering Manufacture, Vol. 225 (2), pp.  247-263.
  12. M. Hazarika, U.S. Dixit and S. Deb, 2010, A setup planning methodology for prismatic parts considering fixturing aspects, International Journal of Advanced Manufacturing, 51, issue 9-12, pp. 1099-1109.
  13. M. Hazarika, U.S. Dixit and S. Deb, 2010, Effect of Datum Surface Roughness on Parallelism and Perpendicularity Tolerances in Milling of Prismatic Parts, Proc. IMechE,  Part B: J. Engineering Manufacture, Vol. 224, no. B9, pp. 1377-1388. 10.1243/09544054JEM1708.
  14. D.K. Sarma and U.S. Dixit, 2009, Environment-friendly strategies for efficient utilization of cutting  tools in finish turning, Transaction of ASME, Journal of Manufacturing Science and Engineering, Vol. 131(6), p. 064506 (5 pages).
  15. M. Chandrasekaran, M. Muralidhar, C. Murali Krishna and U.S. Dixit, 2010, Application of soft computing techniques in machining performance prediction and optimization: a literature review, Int. J. Advanced Manufacturing Technology, Vol. 46 (5-8), pp. 445-464.
  16. D.K. Sarma and U.S. Dixit, Neural network modelling of forces   and indirect prediction of tool    wear in turning of grey cast iron with ceramic tool, Special issue on “Artificial Intelligence Applied in Machining” of International Journal of Machining and Machinability of Materials  
    (IJMMM), vol. 8, nos. ½, 2010, pp. 55-75.
  17. P.P. Gudur and U.S. Dixit, 2009, "An application of fuzzy inference for  studying the dependency of roll force and roll torque on process   variables in cold flat rolling", Int. J. Advanced Manufacturing Technology, DOI: 10.1007/s00170-008-1574-6, Vol. 42(1), pp. 41-52.
  18. P. Kalita, U.S. Dixit, P. Mahanta and U.K. Saha, 2008, A novel energy efficient machine for plate manufacturing from areca palm leaf sheath, Journal of Scientific & Industrial Research, Vol. 67, no. 10, pp. 807-811.
  19. M. K. Sinha, S. Deb and U.S. Dixit, 2009, Design of a multi-hole extrusion process, Materials and Design, Vol. 30, pp. 330-334.
  20. G.V. Durga Prasad, G. Gopa Kishore, Manmohan Pandey and Uday S. Dixit, Numerical Simulations and Design Optimization of the PHT loop of Natural Circulation BWR, Science and Technology of Nuclear Installations, Vol. 2008, Article ID 690357, 12 pages, 2008. doi:10.1155/2008/690357.
  21. P.P. Gudur, M.A. Salunkhe and U.S. Dixit, 2008, A theoretical study on the application of asymmetric rolling for the estimation of friction, International Journal of Mechanical Sciences, Vol. 50, pp. 315-327.
  22. S. Basak, U. S. Dixit and J. P. Davim, 2007, “Application of radial basis function neural networks in optimization of  hard  turning of  AISI D2 cold-worked tool steel with a ceramic tool”, Proc. IMechE, Vol. 221, Part B: J. Engineering Manufacture, pp. 987-998.
  23. P.P. Gudur and U.S. Dixit, 2008“A neural network-assisted finite element analysis of cold flat rolling” , Engineering Applications of Artificial Intelligence, Vol. 21, pp. 43-52.
  24. D. K. Sarma and U.S. Dixit, 2007, “A comparison of dry and air-cooled turning of grey cast iron with mixed oxide ceramic tool”, Journal of Materials Processing Technology, Vol. 190,  pp. 160-172.
  25. S.K. Gunjal and U.S. Dixit, 2007,“Vibration analysis of shape-optimized rotating cantilever beams”, Engineering Optimization, Vol. 39(1), pp. 105-123.
  26. Amit Garg, P.S. Sastry, M. Pandey, U.S. Dixit and S.K. Gupta, 2007, “Numerical simulations and artificial neural network modeling of natural circulation boiling water reactor”, Nuclear Engineering and Design, Vol. 237(3), pp. 230-239.
  27. P. Mahadevan, U.S. Dixit and P.S. Robi, 2007, "Analysis of cold rigid-plastic axisymmetric forging problem by radial basis function collocation method", Int. J. of Advanced Manuf. Tech., Vol. 34(5-6), pp. 464-473.
  28. N.R. Abburi and U.S. Dixit, 2007, Multi-objective optimization of multipass turning processes, Int. J. Adv. Manuf. Tech., Vol. 32(9-10), April, pp. 902-910.
  29. U.S. Dixit, R. Kumar and S.K. Dwivedy, 2006, Shape optimization of flexible robotic manipulators, ASME Journal of Mechanical Design, Vol. 128, pp. 559-565.
  30. N.R.. Abburi and U.S. Dixit, 2006, A knowledge-based system for the prediction of surface roughness in turning process,  Robotics and CIM, Vol. 22/4, pp. 363-372.
  31. D. Kumar and U.S. Dixit, 2006, A slab method study of strain hardening and friction effects in cold foil rolling process, J. Mater. Process. Tech., Vol. 171/3, pp. 331-340.
  32. D.K. Sonar, U.S. Dixit and D.K. Ojha, 2006, Application of radial basis function neural network for predicting the surface roughness in turning process, Int. J. Adv. Manuf. Tech., Vol. 27, no. 7-8, pp. 661-666.
  33. D.K. Ojha and U.S. Dixit, 2005, An economic and reliable tool life estimation procedure for turning, J. Adv. Manuf. Tech., Vol. 26, no. 7-8, pp. 726-732.
  34. A. Kohli and U.S. Dixit, 2005 A neural network based methodology for prediction of surface roughness in turning process, Int. J. Adv. Manuf. Tech., Vol. 25, no. 1-2, pp. 118-129.
  35. S. Chandra and U.S. Dixit, 2004, A rigid-plastic finite element analysis of temper rolling process, J. Mater. Process. Tech., Vol. 152/1, pp. 9-16.
  36. P. S. Robi and U. S. Dixit, 2003,  Application of neural networks in generating processing map for hot working, J. Mater. Process. Tech., Vol. 142/1, pp. 289-294.
  37. U. S. Dixit and S. Chandra, 2003, A neural network based methodology for the prediction of roll force and roll torque in fuzzy form for cold flat rolling process, Int. J. Adv. Manuf. Tech., vol. 22, no. 11-12, pp. 883-889.
  38. K. A. Risbood, U.S. Dixit and A. D. Sahasrabudhe, 2003, Prediction of surface roughness and dimensional deviation by measuring cutting forces and vibrations in turning process, J. Mater. Process. Tech., Vol.132, pp. 203-214.
  39. U. S. Dixit, P. S. Robi and D. K. Sarma, 2002, A systematic procedure for the design of a cold rolling mill, J. Mater. Process. Tech., Vol. 121, pp. 69-76.
  40. U.S. Dixit and P.M. Dixit, 2000, Application of fuzzy set theory in scheduling of tandem rolling mills, ASME J. Manufact. Sci. Engng, Vol. 122, pp.494-500.
  41. U.S. Dixit and P.M. Dixit, 1997, Finite element analysis of flat rolling with inclusion of anisotropy. Int. J. Mechanical Sciences vol. 39, pp. 1237-1255.
  42. U.S. Dixit and P.M. Dixit, 1997, A study on residual stresses in rolling. Int. J. Mach. Tools Manufact., vol. 37, pp. 837-853.
  43. U.S. Dixit and P.M. Dixit, 1996, A finite element analysis of flat rolling and application of fuzzy set theory. Int. J. Mach. Tools Manufact., vol. 36,  pp. 947-969.
  44. U.S. Dixit and P.M. Dixit, 1995, An analysis of the steady-state wire drawing of strain-hardening materials. J.Mater. Process. Tech., vol. 47, pp. 201-229.